Equipment category
2 Roll Plastic Rubber Mills
12 listings currently shown in this equipment category. Open a listing to review its available details and send an inquiry.
12 listings in 2 Roll Plastic Rubber Mills
Browse all inventory →
2 Roll Plastic Rubber Mills
26" x 26" x 84" Stewart Bolling 2-Roll Twin Rubber Mixing Mill, 2-Drilled Front Rolls
2016Akron, OhioStewart Bolling 26" x 26" x 84" twin rubber mill. Recently removed from a rubber manufacturing facility that closed in July of 2023. This mill was rebuilt by Stewart Bolling in 2016. Both front rolls are triple pass "drilled" rolls. Rear rolls are cored. Direct connected and unitized on a 4-piece keyed base with leveling pads. Lufkin T720B 83.5 to 1 reducer. WEG 300 hp 575VAC 1780 rpm motor and starter with dynamic braking. The Lufkin reducer is rated for 400HP. 1.08 friction ratio on both mills. Belly bar safeties on both mills. Akron standard overhead 84" mill blender. Operators control station. A drilled drive roll is also available for either side of this mill. Video of mill running available. Mill can be used as a single 84" left or right hand wrap around design.
View listing and inquire →
2 Roll Plastic Rubber Mills
26" x 26" x 84" Adamson United Rubber or Plastic Mill, 2-Roll, 500 HP with Drilled Rolls
1988Akron, OhioAdamson 26" x 26" x 84" 500HP 2 - roll plastic/rubber mixing mill. Motorized roll adjusters can be replaced with hydraulic cylinders. Direct connected and unitized on a three piece heavy "I" beam steel base with leveling pads. New in 1988. Both rolls are triple pass "drilled" for heating or cooling and have 17" journals. Bearing housings have cored cooling channels for high temperature operation. Inboard and outboard grease seals. Rolls are individually driven to produce a wide range of friction ratios. Each roll is driven via Lufkin model #THB440CH, right angle gear reducer with a 64.69 to 1 ratio. Rated for 250HP with a 1.68 service factor @ 1150 rpm input speed. Each roll has a Reliance 250HP DC 1150 motor driving the reducer. Flip up stock guides. Prodicon overhead blender. There are no SCR drives or controls.
View listing and inquire →
2 Roll Plastic Rubber Mills
22" x 60" Farrel, 2-Roll Left Hand Drive Wrap Around Rubber or Plastic Mill
Akron, OhioFarrel 22" x 22" x 60" mill. Left hand drive. Low profile frames. Space saving "wrap around" design. Pneumatic flip up batch guides. 1.2 to 1 friction ratio. Direct connected via Alten 48 to 1 reducer. 200HP GE 1200 rpm AC 460VAC motor. Two piece keyed base. Pneumatic disc brake. Inboard and outboard grease seals. Positive pullbacks with shear pins. Drawing upon request.
View listing and inquire →
2 Roll Plastic Rubber Mills
28" x 100" Stewart Bolling, 500 HP Hydraulically Driven Mill with Hydraulic Roll Adjusters and Drilled Rolls
2017Akron, OhioStewart Bolling 28" x 28" x 100" 2 roll rubber mill with front and rear "drilled" rolls. 500HP Haaglunds hydraulic variable speed marathon motor direct connected to drive roll. 500HP AC motor inside hydraulic pump cabinet. Hydraulic roll adjusters. 27/29 tooth connecting gears generating a 1.074 friction ratio. All hydraulic components new in 2017. Recently removed from production and in excellent operating condition.
View listing and inquire →2 Roll Plastic Rubber Mills
New RME Lab and Production Mills -- Built to Suit
Akron, OhioNew RME Lab and Production Mills Built to Suit - All sizes up to 16" to 42". Built to your specification.
View listing and inquire →
2 Roll Plastic Rubber Mills
6" x 15" EEMCO Rubber Mill 15 HP Motor Compact Cabinet Design
Akron, OhioEEMCO rubber mill 6" x 15" Compact cabinet design, 15 hp motor Roll Diameter: 6" (152.4 mm) Roll Width: 15" (381 mm) Motor Power: 15 HP Frame Design: Compact Cabinet / Unitized Base Roll Material: Hardened Steel Adjustment Type: Manual Screw-down (Nip Gap adjustment via handwheels) Lubrication: Central Grease or Sight Glass Lubricators Approx. Dimensions: 52" W x 52" D x 72" H Typical Feed Load: 1 to 5 lbs (depending on compound density)
View listing and inquire →2 Roll Plastic Rubber Mills
16" x 42" Kobe Rubber Mill 60 HP, Pneumatic Flip Guides, Unitized
Akron, OhioKobe 16" x 42" 60 hp, pneumatic flip guides, unitized, no motor Manufacturer: Kobe Roll Diameter: 16" Roll Width: 42" Power Requirement: 60 HP (Note: Currently sold without motor) Guides: Pneumatic Flip Guides Base Design: Unitized
View listing and inquire →2 Roll Plastic Rubber Mills
16" x 42" Farrel Rubber Mill, Unitized and Direct Connected
Akron, OhioFarrel 16" x 42" rubber mill unitized and direct connected, no motor Manufacturer: Farrel Roll Diameter: 16" Roll Width: 42" Drive Type: Direct Connected / Uni-Drive Base Design: Unitized (Single heavy-duty steel frame) Recommended Motor: ~60 HP to 75 HP (Sold without motor) Lubrication: Typically compatible with Trabon or similar automatic systems Adjustment: Manual Nip Adjustment
View listing and inquire →
2 Roll Plastic Rubber Mills
22" x 60" Farrel Rubber Mill 150 HP Left Hand Drive, Falk Reducer, Air Brake 150 HP
Akron, OhioFarrel 22 x 60 Rubber Mill 22" x 60" left hand drive, 150 HPalk reducer, with air brake Manufacturer: Farrel Roll Diameter: 22" Roll Width: 60" Drive Configuration: Left Hand Drive Motor Power: 150 HP Gear Reducer: Falk Reducer Braking System: Air Brake Base Design: Heavy-Duty Industrial Frame
View listing and inquire →
2 Roll Plastic Rubber Mills
22" x 22" x 66" Nippon, 2 Roll Mill, Variable Speed/Friction, Rubber or Silicone
Akron, Ohio1-Nippon 22" x 22" x 66" two roll rubber or silicone mill. Direct connected and unitized on a two piece base. Each roll driven via parallel shaft Hansen reducers with separate 60HP variable speed DC motors and SCR's. 120HP total horsepower. This setup has variable speed and friction up to 24 RPM on either the front or rear roll. Mill has "ANTI-FRICTION" roller bearings on both the front and rear roll journals. Front roll is triple pass "drilled" for best heating or cooling capability. Rear roll is cored. Front roll is adjusted via individual motorized roll adjusters. Hydraulic stock pusher and power unit. Manual tilting guides on water side. Automatic oil lubrication.
View listing and inquire →
2 Roll Plastic Rubber Mills
6" x 13" TMP, Roller Bearing Lab Mill, Chromed Rolls, 7.5 HP, Cabinet Mounted
Akron, OhioLike new TMP "Technical Machine Products" 2-roll 6" x 6" x 13" lab mill with chromed rolls. "ROLLER BEARINGS". 7.5 HP 460VAC inverter duty gearhead motor, triple chain drive. Front and rear belly bar safeties. Positive pullback assemblies with flip up batch guides.
View listing and inquire →
2 Roll Plastic Rubber Mills
3" x 7" Farrel, High Temperature Lab Mill 700 Degree Capacity
Akron, OhioFarrel 3" x 3" x 7" 2-roll high temperature lab mill. 700 degree capability. Each roll is chrome plated. Each roll is electrically heated via cal rods with their own temperature controller. Each roll has electric air blowers to cool rolls and maintain set temperatures. Each roll is individually driven via 1-1/2 HP variable speed motor and starter and controls with a 440/3/60 VAC input. 120VAC control voltage. "ROLLER BEARINGS" on roll journals. Micro roll adjusters. Flip up guides. Finger barrier safety above rolls interlocked to front and rear knee safeties. Mill was recently removed from a Bridgestone lab in Akron Ohio. 0 to 30 RPM. Detailed spec sheet upon request.
View listing and inquire →